Maker : M-Tron
Part No. : K1523BA

  Datasheet PDF : K1523BA.pdf
  Cross Reference : K1523BA Cross Reference
  Buy Component : K1523BA Find Stock and Price

Shortcut : K1523BA  K1523BA 

Product Information

K1523BA Series 5V Voltage Controlled Crystal Oscillators Applications: Phase-Locked Loops (PLL’s); Clock Recovery; Reference Signal Tracking; Synthesizers; Frequency Modulation/Demodulation 2.0 to 35.0 MHz Frequency Range 0.5V to 4.5V Control Voltage ±25ppm Stability Variety of Deviation Sensitivity Options -40°C to 85°C Operating Temperature ax. mM ,8 m 20 ax. mM ,2 m 13 E 23BA Z K155.000 MH E COD 3 TI DAT C m 1m 8,5 x. Ma PIN 1 Not Recommended for New Designs. Refer to K1570A & K1570AQH Series as an Alternative. E L E C T R I C A L S P E C I F I C AT I O N S Model Frequency Range (MHz) Input Current (mA) Frequency Control Function Deviation (ppm) Minimum Maximum Linearity (%) Modulation Bandwidth (±3dB) Nominal Control Voltage (V) Control Voltage Range (V) Transfer Function Input Impedance Frequency Stability (ppm) Overall 0oC to +70oC -40oC to +85oC Temperature Range (oC) Operating Storage Supply Voltage (V) Symmetry (%) CMOS/TTL Start Up Time (ms) Typical SSB Phase Noise (dBC/Hz) Offset from Carrier 10Hz 100Hz 1KHz 10KHz 100KHz 45/55 <10 -65 -95 -120 -140 -150 -40oC to +85oC -40oC to +125oC +5.0V ±5% 40/60 Inclusive of Calibration, Temperature, Voltage, Load and Aging ±25 ±50 ±40 ±55 > 2KHz 2.5 0.5 to 4.5 Positive > 50KΩ @ 10KHz ±100 ±150 <5 > 20KHz ±100 ±190 < 10 2 to 16 < 17 16 to 25 < 19 K1523BA 25 to 33 < 26 33.1 to 35 (For Custom Deviation Range, Vc Range, etc. - Consult Factory) PA R T N U M B E R I N G G U I D E K1523BA X - Specify Frequency “Blank” = 0°C to 70°C Operating Temp. “M” = -40°C to +85°C Operating Temp. 2553 N. Edgington Street, Franklin Park, IL 60131 Phone: 847.451.1000 Fax: 847.451.7585 800-888-1499 or www.champtech.com 1 K1523BA Series 5V Voltage Controlled Crystal Oscillators PIN 1 7 8 14 FUNCTION Voltage Control Gnd/ & Case Gnd Output + VCC SHIPPING TUBE CROSS SECTION OUTPUT WAVEFORM TEST CIRCUIT DIAGRAM MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS Temperature Cycle Mechanical Shock Vibration Humidity Steady State Thermal Shock Electrostatic Discharge Solderability Hermeticity Resistance to Soldering Lead Integrity Marking Permanence Life Test REFERENCE PROCEDURES MIL-STD-833, Mtd 1010, Cond. B MIL-STD-883, Mtd 2002, Cond. B MIL-STD 883, Mtd 2007, Cond. B MIL-STD-202, Mtd 103 MIL-STD-883, Mtd 1011.7 Cond. B MIL-STD-883, Mtd 3015 Class II MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 DESCRIPTION -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell 1500 g’s 20-2000 Hz; 0.06 inch; 15g’s; 3 planes 40°C; 90%-95% R.H.; 56 days 100°C to 0°C; Water-to-Water; 15 cycles 2 KV to 4 KV Threshold Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He MIL-STD-202, Mtd 210D, Cond. C 260°C; 10 seconds: 1 inch/sec. MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum 2553 N. Edgington Street, Franklin Park, IL 60131 Phone: 847.451.1000 Fax: 847.451.7585 800-888-1499 or www.champtech.com 2 ...

Link URL